888-721-8283
Contaminant Treatment Guide

How Each Contaminant Class Is Actually Treated

Eight contaminant problems, each answered the same way: what the controlling problem is, which technology addresses it, and the failure mode that decides whether the remedy holds. Written by the crew that designs the injection programs, not a reagent catalogue.

At a glance

Contaminant situationControlling problemLead technology
BTEX and GRO in groundwaterOxygen delivery to the plumeEnhanced aerobic bioremediation
Creosote and coal tar (MGP)DNAPL mass and very high oxidant demandISGS soil mixing, or thermal at shallow depth
PCE and TCE in clayNo advection, back-diffusion tailFracture emplacement of EZVI
Former dry cleaner (PCE)Vapor intrusion, then vinyl chloride riskVI mitigation, then ERD with bioaugmentation
Hexavalent chromium in soilChromate mobility and pH sensitivityISCR to insoluble Cr(III)
TPH at a fuel terminalFraction-specific standards, leaching to groundwaterLNAPL recovery plus aerobic bioremediation
Mixed petroleum and chlorinated NAPLOpposing redox requirementsPersulfate oxidation, then reductive polishing

BTEX and gasoline range organics

BTEX and gasoline range organics (GRO, roughly C6 to C10) in groundwater are best treated with mass removal followed by enhanced aerobic biodegradation. Benzene, toluene, ethylbenzene and xylenes biodegrade readily when oxygen is present, so the controlling variable is oxygen delivery, not chemical addition. Remove free product and source mass first, then deliver oxygen to the dissolved plume.

Why it works, and where it fails

Aerobic bacteria use BTEX as a carbon source with oxygen as the electron acceptor, converting it to carbon dioxide and water. In the field this means biosparging, oxygen-release compounds, or dissolved-oxygen injection sized to the total hydrocarbon oxygen demand — not just to the BTEX concentration. Ethanol or other oxygenates in the fuel compete for the same oxygen and can multiply the demand several times over.

Typical IET approach

LNAPL recovery where free product is present, soil vapor extraction or multi-phase extraction in the vadose and smear zone, then enhanced aerobic bioremediation for the dissolved phase with monitored natural attenuation across the dilute fringe.

BTEX remediation services

Creosote and coal tar at former MGP sites

At a former manufactured gas plant, the controlling problem is dense coal tar mass, not the dissolved plume. In situ geochemical stabilization by soil mixing is the most reliable approach for deep tar zones because it reduces mass flux and leaching without requiring the tar to be destroyed in place. Thermal treatment works for shallow source zones; simple oxidant injection rarely does, because coal tar has an extremely high natural oxidant demand.

Why it works, and where it fails

Coal tar and creosote are DNAPLs — denser than water, pooling on low-permeability layers, and loaded with PAHs such as naphthalene. Their oxidant demand is so high that the reagent consumed by the tar matrix dwarfs what reaches the contamination, which is why ISCO doses become uneconomic. Stabilization binds the tar within a treated matrix, cutting the flux feeding the plume; thermal approaches physically recover or destroy the tar at shallow depth.

Typical IET approach

ISGS soil mixing through the tar zone for deep or inaccessible source mass; electrical resistance or thermal conduction heating where the source is shallow and recovery is practical; DNAPL recovery for pooled tar; monitored natural attenuation or containment for the dissolved plume.

ISGS stabilization technology

PCE and TCE in low-permeability clay

Chlorinated solvents like PCE and TCE in low-permeability clay are the hardest routine case in remediation. Advective delivery fails in clay, and contamination stored in the matrix diffuses back into treated zones for years, so the answer is to create flow pathways, deliver a reductant into them, and set endpoints on mass flux rather than on a single concentration snapshot.

Why it works, and where it fails

At hydraulic conductivities around 10⁻⁶ to 10⁻⁸ cm/s, injected fluid will not penetrate the formation and treatment stalls at the interface. Contaminant mass held in the clay matrix then back-diffuses into the swept zone, producing the long tail that makes these sites appear to fail. Creating a fracture network — by controlled hydraulic fracturing or direct-push fracturing — gives the amendment a path, and emulsified zero-valent iron migrates into those fractures and degrades the solvent in direct contact.

Typical IET approach

Controlled hydraulic fracturing or direct-push fracture emplacement of EZVI or zero-valent iron, sequenced over multiple rounds; thermal treatment where depth and budget allow; mass-flux-based performance monitoring instead of concentration-only endpoints.

EZVI for low-permeability source zones

PCE at a former dry cleaner

A former dry cleaner with PCE contamination follows a phased strategy: protect the receptor first, remove or treat source mass second, then manage the dissolved plume. Vapor intrusion mitigation in any occupied building comes before cleanup, because occupants are exposed for the years a remedy takes to work.

Why it works, and where it fails

PCE degrades through TCE, cis-1,2-DCE and vinyl chloride — each step more mobile, and vinyl chloride far more toxic than the parent compound. That means a remedy that only partially dechlorinates can make the risk picture worse. Complete reductive dechlorination to ethene requires the right electron donor, adequate residence time, and the Dehalochlorella-class organisms that carry out the final steps, which is why bioaugmentation is often paired with donor addition.

Typical IET approach

Sub-slab depressurization or vapor intrusion mitigation in occupied structures; excavation of shallow soils beneath the former machine area; EZVI or ISCR injection into deeper source zones; enhanced reductive dechlorination with bioaugmentation for the plume; monitored natural attenuation at the dilute fringe.

Chlorinated solvent remediation

Hexavalent chromium in soil

Hexavalent chromium in soil is treated by reducing Cr(VI) to Cr(III) in place, converting a soluble, mobile and carcinogenic species into an insoluble hydroxide that stays put. In situ chemical reduction with ferrous sulfate, sodium dithionite, calcium polysulfide or zero-valent iron is the standard approach, and pH control decides whether it holds.

Why it works, and where it fails

Cr(VI) travels as chromate and dichromate anions, which do not adsorb and do not precipitate — they move with groundwater. Reducing to Cr(III) precipitates Cr(OH)₃ at near-neutral pH, removing it from the transport pathway. The traps are pH and re-oxidation: Cr(III) becomes amphoteric and re-mobilizes above roughly pH 10, and manganese oxides or high dissolved oxygen can re-oxidize the chromium back to Cr(VI) over time.

Typical IET approach

ISCR injection of a reductant with pH buffering, verification by both total chromium and leaching tests (TCLP or SPLP) rather than totals alone, and stabilization/solidification by soil mixing where leaching to groundwater is the driver.

Heavy metals stabilization

TPH in soil at a fuel terminal

Reaching TPH cleanup standards at a fuel terminal starts with defining the standard, not choosing a technology. Most states regulate TPH by carbon range — GRO, DRO and ORO — with risk-based or leaching-based numbers, plus separate limits for BTEX, MTBE and naphthalene. Once the applicable fractions are known, the remedy is LNAPL recovery plus enhanced aerobic bioremediation, with source excavation where tank basins are accessible.

Why it works, and where it fails

TPH is not one compound: the carbon-range split exists because lighter fractions are volatile and readily biodegraded while heavier fractions behave more like a persistent oil. A single total-TPH number can hide an exceedance in one fraction. Leaching-based standards add a second constraint, requiring that soil concentrations not drive groundwater above its own standard.

Typical IET approach

Free product and LNAPL recovery; dual-phase extraction or soil vapor extraction in the vadose zone; enhanced aerobic bioremediation with oxygen release for dissolved and smear-zone mass; excavation of hot spots at tank basins and dispenser islands where access allows.

Petroleum hydrocarbon remediation

Mixed NAPL — petroleum and chlorinated solvents

A mixed NAPL plume containing both petroleum and chlorinated solvents needs a sequenced treatment train, not a single chemistry. Oxidize the petroleum mass first, then apply reduction or biological polishing to the chlorinated fraction. Reversing that order wastes the oxidant on petroleum and leaves the chlorinated DNAPL largely untouched.

Why it works, and where it fails

Petroleum hydrocarbons and chlorinated ethenes respond to opposite redox conditions. Petroleum is readily destroyed by oxidation and readily biodegraded aerobically; PCE and TCE require reduction. In co-mingled source zones the petroleum also exerts a large oxidant demand that shields the chlorinated mass. Alkaline-activated persulfate is the usual first stage because it oxidizes both aromatic and chlorinated compounds to a degree; permanganate alone oxidizes chlorinated ethenes but is ineffective against the petroleum aromatics.

Typical IET approach

Alkaline-activated persulfate for the petroleum fraction with close geochemical monitoring; then enhanced reductive dechlorination or zero-valent iron for residual chlorinated mass and daughter products; expect secondary geochemical effects — pH excursions, metals mobilization, manganese and hexavalent chromium generation — and plan monitoring for them.

Mixed contamination approaches

Monitored natural attenuation vs. active treatment

MNA is the cheapest remedy on paper and the most expensive on a 20-year calendar. It belongs at the dilute fringe of a plume with demonstrated degradation — not on a source zone with a receptor.

MeasureMonitored natural attenuationActive in situ treatment
Timeframe to closureYears to decadesMonths to a few years
Up-front capitalLowModerate to high
Monitoring burdenLong — often 10+ years of samplingFocused, 1 to 3 years post-injection
Best suited toDilute plumes with demonstrated degradation and no receptor riskSource mass, high concentrations, receptor exposure, or a closure deadline
Main riskPlume migration or a shifting receptor pathway during a long timelineRebound, incomplete treatment, and geochemical side effects

Contaminant treatment questions

How do you remediate BTEX and gasoline range organics in groundwater?

By combining mass removal with enhanced aerobic biodegradation. BTEX compounds biodegrade readily when oxygen is present, so the controlling variable is oxygen delivery. IET typically recovers free product and treats the smear zone with vapor or multi-phase extraction, then delivers oxygen to the dissolved plume through biosparging or oxygen-release compounds sized to total hydrocarbon demand, with monitored natural attenuation across the dilute fringe.

What is the best treatment for creosote and coal tar at a former MGP site?

The controlling problem is coal tar mass, not the dissolved plume. For deep tar zones, in situ geochemical stabilization by soil mixing is the most reliable approach because it cuts mass flux and leaching without needing to destroy the tar in place. Thermal treatment suits shallow sources. Oxidant injection is usually uneconomic at MGP sites because coal tar has an extremely high natural oxidant demand.

How are chlorinated solvents like PCE and TCE treated in low-permeability clay?

By creating flow pathways, delivering a reductant into them, and measuring mass flux rather than a single concentration. Clay will not accept injected fluid, and contamination held in the matrix back-diffuses into treated zones for years. Controlled hydraulic fracturing or direct-push fracture emplacement of emulsified zero-valent iron is the standard approach, sequenced over multiple rounds with mass-flux-based performance monitoring.

What is the standard approach for cleaning up a dry cleaner site with PCE contamination?

A phased approach: vapor intrusion mitigation in any occupied building first, source mass removal or in situ treatment second, dissolved plume management third. PCE degrades through TCE and DCE to vinyl chloride, which is more mobile and far more toxic than the parent, so the remedy must support complete dechlorination — typically electron donor addition with bioaugmentation — rather than partial degradation.

How is hexavalent chromium stabilized in soil at an industrial site?

By reducing Cr(VI) to insoluble Cr(III) in place using in situ chemical reduction with ferrous sulfate, sodium dithionite, calcium polysulfide or zero-valent iron. Cr(VI) travels as chromate and does not adsorb, so reduction and precipitation is the only way to stop migration. pH control is critical because Cr(III) re-mobilizes above roughly pH 10, and leaching tests — TCLP or SPLP — verify the result better than total chromium.

Is monitored natural attenuation slower than active in situ remediation?

Yes, substantially. Monitored natural attenuation typically takes years to decades to reach closure compared with months to a few years for active treatment. MNA carries low up-front capital but a long monitoring burden and the risk that the plume or a receptor pathway changes during that timeline. It is appropriate for dilute plumes with demonstrated degradation and no receptor exposure.

Not sure which class your site falls into?

Send us the lab data and site plan. IET will tell you which of these pathways applies, what the controlling problem is, and what it will take to close the site — before you commit to a reagent budget.